Parts Q&A

Question 1

Will this work when replacing a Polaris autoclear plus system? View answer

Asked 8 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 2

Is this better than a regular eyeball water return? If so, why? View answer

Asked 8 ´years ago | Parts > Vector Jet

Question 3

Will this dummy cell fit my IC20 View answer

Asked 3 ´years ago | Parts > Bypass Cell (fits Pentair® IntelliChlor® Salt Systems)

Question 4

Hi. My display isn’t readable on my Aqua Rite from Goldline. Do you carry a replacement? I can send a photo if needed. View answer

Asked 4 ´years ago | Parts > Replacement Display PCB for Hayward® AquaRite® Circuit Board GLX-PCB-DSP (Aftermarket)

Question 5

I have a SJ-30, I need to reduce it down to 1 1/2"". What to I need to buy from you to do that View answer

Asked 2 ´years ago | Parts > CircuPool SJ Adapter Kit (from existing RJ-Classic Models)

Question 6

Does this gasket go between the salt generator and the housing? View answer

Asked 4 ´years ago | Parts > SGS Breeze O-Ring

Question 7

I have the Classic RJ30. I am looking to replace the large rubber rings that the cell housing fits onto the pvc piping and the o-rings that are on the cell housing as well? View answer

Asked 6 ´years ago | Parts > CircuPool RJ-Classic O-Ring Set

Question 8

I'm converting from a Zodiac and want to be sure the spacing works. Is the 6 1/2"" shown in the picture a center to center measurement or end to end? View answer

Asked 6 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 9

What's the length of the pipe? View answer

Asked 9 ´years ago | Parts > Bypass Cell (fits Hayward® Aquarite®, Swimpure Plus®, CircuPool RJ, CircuPool Si)

Question 10

I just purchased the Edge 40 and will likely need to install it vertically. Will this kit work with the Edge 40? View answer

Asked 2 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 11

I have a CircuPool CORE-15 Salt Chlorine Generator, it's about 8" between the intake and outflow. Will the CircuPool SJ - Hayward/Pentair Cell Adapter Kit fit for that? If not, is there another kit to make it easier? View answer

Asked 4 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 12

How tall is the vertical installation kit? View answer

Asked 7 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 13

Will this work on Pentair IC20? View answer

Asked 6 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 14

vertical installation kit. what size pvc: 1-1/2"" or 2""? View answer

Asked 4 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 15

What is the measurement required for the cut out to fit this into an existing line? I have an older Jandy cell, will this fit? View answer

Asked 8 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 16

I have a Pure Chlor Salt System that cut pipe at 113/4"" will Hayward sytle adapter work??? View answer

Asked 5 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 17

I have a CPSC36 unit, it has cracks all in it. Will the clear replacement fit my unit? View answer

Asked 8 ´years ago | Parts > CompuPool Clear Housing Fits All CPSC

Question 18

Will this fit Hayward T15, 40k gallon cell? View answer

Asked 3 ´years ago | Parts > Convenience Kit - Value Pack

Question 19

Will this work on my system. I bought a salt cell T15 from you guys. The board reads 4000 amount of salt. I got it checked by Pinch a Penny pool store and it said 3100. I think the board is bad. Then i put my old salt cell back on and it read 3500 but it stills generating chlorin. The new salt cell does the same thing. View answer

Asked 4 ´years ago | Parts > Replacement Power PCB for Hayward® AquaRite® Circuit Board GLX-PCB-RITE (Aftermarket)

Question 20

What exactly does the "winter" mode do and how is it used on the RJ60 generator? View answer

Asked 3 ´years ago | Parts > Bypass Cell (fits Hayward® Aquarite®, Swimpure Plus®, CircuPool RJ, CircuPool Si)

Question 21

I bought the phosphate test strip kit from you. I says I need to dip strip in a vial and compare water color change to card for phosphate level. What vial? There was none in kit and there is no reference to vial size in documentation. Without it strips are useless...help!! View answer

Asked 3 ´years ago | Parts > Convenience Kit - Value Pack

Question 22

I have pentair equipment on my salt water system, I have an electronic switching system for exterior lights, spa, waterfall etc. which transmits wireless signals to my electrical enclosure outside.Can I find a replacement for it? Cost etc.?? View answer

Asked 6 ´years ago | Parts > Bypass Cell (fits Hayward® Aquarite®, Swimpure Plus®, CircuPool RJ, CircuPool Si)

Question 23

Is this for 1.5"" or 2"" pipe? View answer

Asked 8 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 24

I have old zodiac clearwater lm2-24, can this product replace that? My pool is only 17,500 gals. Also is there a direct fit conversion or will this cell work in my existing plumbing. Thanks View answer

Asked 4 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 25

Will this work with a Circupool Si-30 series generator? View answer

Asked 4 ´years ago | Parts > Replacement Power PCB for Hayward® AquaRite® Circuit Board GLX-PCB-RITE (Aftermarket)

Question 26

I have a Compupool system. Will this fit or do I even need an adapter ? View answer

Asked 4 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 27

will this work with comu pool CPSC48 cell View answer

Asked 4 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 28

What is the center to center of the upright pipes without the elbows?I have a compu pool generator with the 4 1/2" center to center and no room to cut the pipes and redo them View answer

Asked 5 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 29

What parts exactly does the kit include? Thank you View answer

Asked 5 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 30

can Circupool vertical be set up horizontally? Have RJ 30; problems with space. View answer

Asked 7 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 31

Does it matter whether the flow sensor is before or after the cell? View answer

Asked 3 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 32

Is this for 1.5" or 2" pipe? View answer

Asked 8 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 33

Universal Si40: Will the inlet (cord side) be reversed for vertical installation, the way it is pictured in your example? View answer

Asked 6 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 34

Will this fit for a Jandy PLC1400? View answer

Asked 8 ´months ago | Parts > Bypass Cell (fits Pentair® IntelliChlor® Salt Systems)

Question 35

Hi I have a RJ45, can I clean the cell with vinegar instead of muratic acid? View answer

Asked 4 ´years ago | Parts > CircuPool O-Ring Set for RJN and Universal / Si

Question 36

My question is: will the Clear Housing for a SGS Breeze fit on all your unit ie 320, 540, 760,Only asking cuz I did purchase one today 8-9-21 and I'm pretty sure the my is the 540 View answer

Asked 4 ´years ago | Parts > Saline Generating Systems Clear Housing for SGS Breeze, Wave, and CMP PowerClean

Question 37

I have the CircuPool Core 35 series and my system error LED light is blinking..I have made sure I cleaned the cell with acid and my pool chemistry is correct and there is a small drip under the control panel. Will these rings help seal that better and maybe correct the light flashing? View answer

Asked 4 ´years ago | Parts > CircuPool RJ-Classic O-Ring Set

Question 38

I have a 2005 model Goldline controls, Aqua Rite electronic salt generator with a T-15 cellwhat is the correct computer board to replace old one? View answer

Asked 4 ´years ago | Parts > Replacement Power PCB for Hayward® AquaRite® Circuit Board GLX-PCB-RITE (Aftermarket)

Question 39

For this union i need the flat washer/gasket. Where can i get that please. View answer

Asked 3 ´years ago | Parts > Replacement Union - RJ Classic Models

Question 40

Is this available in a 1.5” version, or can the anode be relocated into a 1.5” tee? View answer

Asked 11 ´months ago | Parts > Solaxx Inline 2" Zinc Anode & Water Bond with Copper Wire

Question 41

I have a Rheem 399000 BTU mod RHIM-15-9977 LP heater already installed running. Will your product wireless remove interface with my unit ? View answer

Asked 4 ´years ago | Parts > AutoPilot PoolSync Wifi Connector

Question 42

Is the cleaning stand for the I 60 salt generator? View answer

Asked 3 ´years ago | Parts > Cleaning Stand (fits Pentair® IntelliChlor® Salt Systems)

Question 43

Size of Union??? Both ends? View answer

Asked 5 ´years ago | Parts > Replacement Union - RJ Classic Models

Question 44

Will these o rings work in a edge 25 series CircuPool union? View answer

Asked 10 ´months ago | Parts > CircuPool RJ-Classic O-Ring Set

Question 45

how much pipe do you remove to install the check valve View answer

Asked 10 ´months ago | Parts > Check Valve - Premium, Corrosion Resistant - 2-in.

Question 46

how do i replace the fuse in a circu pool rj control ? View answer

Asked 8 ´years ago | Parts > 5-Amp Fuse Reset Button (CircuPool RJ-Classic Models Only)

Question 47

Will the sj35 cell work with the jacuzzi’s when it’s heater is on? View answer

Asked 2 ´years ago | Parts > CircuPool SJ - Hayward®/Pentair® Cell Adapter Kit

Question 48

I have just enough space to maybe not use this but if I decide to get this. I have 2 questions. The 1st is will it decrease pressure in the system because of adding a vertical section. So I would have to run my vari. Pump at a higher setting? And the second is could I put this in horizontal? Thanks. View answer

Asked 5 ´years ago | Parts > CircuPool Vertical Installation Kit

Question 49

I have a NSF model 52000 salt water generator and my cell housing cracked. I need a replacement View answer

Asked 9 ´months ago | Parts > Saline Generating Systems Clear Housing for SGS Breeze, Wave, and CMP PowerClean

Question 50

What are the dimensions of the O-Ring? The xxxx on cover I have is 5" across and 4 5/8" just inside the lip of the cover. I do not see any groove in the clear housing for an O-Ring. I have the Breeze Salt Generating System Model 760 and we just replaced the housing. View answer

Asked 1 ´year ago | Parts > SGS Breeze O-Ring

Parts Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools