I am having my pool Replastered 32k Inground next few months. Currently use chlorine tabs. I use city water so after Cleaning my filter and putting in new sand will it be ok to just start it up normally and then test the water ? View answer
Asked 3 ´years ago | Sale > CircuPool CORE-55 Salt Chlorine Generator
Will this fit Hayward T15, 40k gallon cell? View answer
Asked 3 ´years ago | Parts > Convenience Kit - Value Pack
How long is the item? View answer
Asked 3 ´years ago | Parts > Bypass Cell (fits Pentair® IntelliChlor® Salt Systems)
Will this dummy cell fit my IC20 View answer
Asked 3 ´years ago | Parts > Bypass Cell (fits Pentair® IntelliChlor® Salt Systems)
Is there a way to recalibrate the temperature sensor? My pool waterheater and pool thermometer both indicate that the pool is at 69 degrees F. But the readout on my RJ-60+ shows the water temp. to be around 50 deg F. As a result, the RJ-60+ is not generating any chlorine. It says that the temp. Is too low. Is there anything that I can do to correct the discrepancy in temperature. Charles View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Are the 10,000 hours the running time hours or the chlorine making hours because it does not make chlorine in the cold weather. Is there paperwork explaining error codes?What Is limited in the warranty? View answer
Asked 3 ´years ago | Sale > APX PERFORMANCE P60 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC60® Salt Cells | up to 60,000 gallons
The red ""salt level"" light is blinking and the display message on the controller says ""WARNING: ADD WATER"" The unit will not generate chlorine. My salt level is fine and my pool chemistry is perfect, but I am having to manually add chlorine. I cannot find anything about this error in the owners manual or online. View answer
Asked 3 ´years ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
I own an CircuPool Rj 20 (RJ20NR) that I purchased from your company on 6/5/2017 order# DSP-31637. I am looking for a replacement cell and wanted to male sure that I order the correct replacement. Is the RJ20C-RC-4Y the direct correct replacement for the housing I have? Thank you in advance for your reply. View answer
Asked 3 ´years ago | Salt Cells > CircuPool RJ20/AG16 Classic Replacement Cell (Electrode Only)
Can you add hose to purge end? View answer
Asked 3 ´years ago | Filters > CircuPool TJ-16 "Typhoon" Centrifugal Pre-Filter
I currently have an RJ 20 plus that has performed well in my 16,000 gallon pool. The cell has now gone bad and needs replacing. Is there a benefit to upgrading to the RJ 30 plus cell and is it compatible with my old control unit? View answer
Asked 3 ´years ago | CircuPool RJ-20 PLUS Salt Chlorine Generator
I just bought a CircuPool SmartFlo VS 1.5. How long should it take to prime? I have filled basket up and turned pump on and opened pressure valve on filter. In videos it seems like it only takes a few seconds for water to start coming out of pressure valve on filter. I have left my pump on for 3-4 min and never get water. Shut off pump cause afraid of hurting something. Should I leave on longer? View answer
Asked 3 ´years ago | Manufacturers > CircuPool > CircuPool SmartFlo® Variable Speed Pool Pump - 1.7 THP
<!--IT says you can upgrade from edge 25 to edge 40 for a dollar. -->My question is are both edge 25 & 40 compatible with each other so when the cell goes, I can replace the cell with the edge 25 or do I have to stay with the edge 40 View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool EDGE-25 Salt Chlorine Generator
Currently there is a check valve on the return from my heater back into pool. I know the chlorine generator needs to be the last thing on the return before going back to pool. My question is does the check valve need to stay on between the heater and pool or can it be eliminated from the equation? If needs to stay there should check valve be before or after the chlorine generator? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool CORE-15 Salt Chlorine Generator
Just installed this, replacing my Intellichlor40, and the Salt Level light is blinking red. I check the salinity level and its at 4790, which is just over the 4500 for the ideal range. Will this unit still produce chlorine with this level of salt and the Salt High light blinking? Thank you. View answer
Asked 3 ´years ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
What are the dimensions, primarily length of the salt generator cell/container and the flow sensor conduit? I have limited space between my heater and the returns to the pool and spa and need to make sure this will fit with the additions 12” from the heater to the flow sensor. Thanks Sean View answer
Asked 3 ´years ago | Sale > CircuPool RJ-30 PLUS Salt Chlorine Generator
Is this package compatible with the Pentair Easytouch automation system at our new home. The existing Easytouch system seems to still be in great shape, but the pump, filter canister and chlorinator are on their last leg. View answer
Asked 3 ´years ago | Packages > Ultimate Combo (Medium Pools) - (RJ-30 PLUS Salt System, SmartFlo® 1.7 THP VS Pump, and CJ-150 Cartridge Filter)
I have a Pentair IC40 today. I like this option. Will it plug directly into the old 4 pin outlet on the Intellitouch that was previously used by the IC40? I understand that it will not transmit data, but what exactly will not work on the Intellitouch? I'm guessing I won't be able to program it from the Intellitouch display, but that isn't a big deal. What about flow signals? View answer
Asked 3 ´years ago | Sale > APX PERFORMANCE P60 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC60® Salt Cells | up to 60,000 gallons
Have Breeze 540 w/ only 1 maybe 2 cells generating chlorine. Is cell assembly gone bad or is a computer chip failed again? View answer
Asked 3 ´years ago | Salt Cells > APX PERFORMANCE S5 Aftermarket Replacement Cell fits Saline Generating Systems® Breeze® 540 (now CMP® PowerClean Salt® or Jacuzzi® JSCS40)
I have a Jandy AquaLink RS system but dont know how loosing the "RS-485 or data connection" will affect me? The AquaLink RS has an indoor control panel program timer to automatically start/stop the equipment - will this salt cell still start/stop on that timer? View answer
Asked 3 ´years ago | Sale > APX PERFORMANCE P60 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC60® Salt Cells | up to 60,000 gallons
