We have a regular chlorinated pool that we are considering switching over to salt. We started looking because we were looking for a new filter and found one that is a filter with pump and salt water system. Is that all that is needed to switch over to salt water? I've seen you do not need to change your filter to switch to a salt system but that's the main thing we do want to change. we have a 24 ft round above ground pool View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool EDGE-15 Salt Chlorine Generator
Does the SJ-40 have reverse polarity? View answer
Asked 8 ´years ago | Salt Chlorinators > CircuPool SJ-45 Salt Chlorine Generator
I have variable speed pump that has its own controller, so it is powered on all the time. Can I connect the CircuPool system to continous power and let the flow sensor determine when the system should generate chlorine? Otherwise I would need to manually coordinate a timer so that the CircuPool only comes on when the pump is running, and I'd rather not do that. View answer
Asked 7 ´years ago | Salt Chlorinators > CircuPool RJ-60 PLUS Salt Chlorine Generator
I have a variable speed pump and I am concerned about the minimum flow rate required for this unit. Does this unit have a flow rate sensor that shuts the unit off if the flow rate is below 30gpm? I'm not sure what my flow rate is at low RPM, but I want to make sure this unit will operate. View answer
Asked 8 ´years ago | Salt Chlorinators > CircuPool SJ-45 Salt Chlorine Generator
I have the RJ45 system that is about 8 years old. It turns on but does not generate chlorine unless I restart the system and select max. How do I determine if the electric cell is bad or the display control module? View answer
Asked 4 ´years ago | Salt Cells > CircuPool RJ45 Classic Replacement Cell (Electrode Only)
Will this work on a 220 volt View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool SJ-35 Salt Chlorine Generator
I have an above ground pool, my current pump has a regular plug but according to the SJ-35A system, they both have to be hard wired into a timer. Can I not purchase a plug for the SJ-35A to plug into a timer or do I have to have my pump cord changed? View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool SJ-35 Salt Chlorine Generator
Will a intex 1103 cell fit this houing View answer
Asked 5 ´years ago | Parts > CircuPool Clear Housing for RJ Classic
I have about 22 inches of straight pipe where I want to install this. If installing the flow switch and inverted cell on the same straight pipe, is the 6-12” of pipe before the flow switch required? Since it is the same straight pipe, can it be less? Or will the flow have to be installed after the cell? View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have two questions. First: Can this system re-place my existing Jandy/Zodiac nature 2 Fusion Soft System without changing plumbing? Second: I have a 38,000 gallon pool with a Jandy VS Stealth pump that I am currently replacing too. What size salt system/chlorine generator should I purchase?(after 4 years of trouble shooting and constant maintenance and cost, I have come to HATE Jandy products). View answer
Asked 8 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
What heater is best for a small pool? View answer
Asked 6 ´months ago
Is the SJ-20 Series run on 110Volts? View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool SJ-35 Salt Chlorine Generator
Circupool not generating clorine? View answer
Asked 6 ´years ago | Salt Chlorinators > CircuPool SJ-35 Salt Chlorine Generator
Do you sell pool heaters View answer
Asked 1 ´month ago
Does this part include the o-ring? View answer
Asked 7 ´years ago | Parts > Replacement Union - RJ Classic Models
I have the Pentair EasyTouch automation center and the IC40 salt cell, which is bad now. Will the APX P40 or P60 work with the controller. I just need power from the EasyTouch correct? It won't read salt level or any control from the EasyTouch unit Correct. Also, can I use the P60 instead of the P40. We have 38500-gallon pool. View answer
Asked 10 ´months ago | Salt Cells > APX PERFORMANCE P40 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC40® Salt Cells | up to 40,000 gallons
Are there directions for replacing the cell? My unit is about 4 years old and I am guessing I need to replace the cell. The cell doesn't appear to be exactly like the one I currently have. Any help is appreciated. View answer
Asked 9 ´years ago | Salt Cells > APX PERFORMANCE C4 Aftermarket Replacement Cell fits CompuPool CPSC-16 | up to 16,000 gallons
Can the salt cell be mounted at a slight upward angle or does it need to be perfectly horizontal or vertical. I have a good location to mount the cell but it is on a slight upward, approximately 15 degree angle. I would think it would be fine, bu I just wanted to verify for sure. View answer
Asked 6 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
When I was reading the installation instructions for the RJ45 plus, it states if using with a variable speed pump (on a low speed setting) that the cell must be inverted. If I'm installing the RJ45 plus vertically, does that mean I can't use the low speed on my variable speed pump? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
