What are the dimensions of the O-Ring? The xxxx on cover I have is 5"" across and 4 5/8"" just inside the lip of the cover. I do not see any groove in the clear housing for an O-Ring. I have the Breeze Salt Generating System Model 760 and we just replaced the housing. View answer
Asked 1 ´year ago | Parts > SGS Breeze O-Ring
I have the CircuPool Universal25 system and it's getting pretty old. The xxxx to control the chlorine production does not stay on the number it is set at and it's nearly impossible to select a number as it is too sensitive to movement. I'm considering upgrading to the RJ-20 system and wanted to know if the salt cell will fit into the plumbing connections I have in place for the Universal cell?? View answer
Asked 3 ´years ago | CircuPool RJ-20 PLUS Salt Chlorine Generator
Is the ""low salt"" and ""high salt"" determined in the RJ-45 Plus salt generating cell? I have lately have had the controller show ""low salt"" and ""check cell"" and I have carefully cleaned the cell as instructed 3 times in the last 4 weeks View answer
Asked 5 ´years ago | Salt Cells > CircuPool® RJ-45 PLUS Replacement Cell
Have a pool using a Hayward Aqua-rite T-3 is this T-9 a direct replacement? Would like to increase output. I know I will have to reprogram the control unit. Are control units same for all sizes of cells? When I say direct replacement I mean no plumbing, just unscrew old and xxxx on the new plus reprogram of course. View answer
Asked 8 ´years ago | Salt Cells > CircuPool® CIR-GEN9 Aftermarket Replacement Cell fits Hayward® AquaRite® 25,000 Gal. Models
Has anyone had a problem with their control panel not getting power? My pump will run but no display or power on the control panel. wired it according to instructions, checked the internal fuse and try the reset button. Nothing View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Is there a way to recalibrate the temperature sensor? My pool waterheater and pool thermometer both indicate that the pool is at 69 degrees F. But the readout on my RJ-60+ shows the water temp. to be around 50 deg F. As a result, the RJ-60+ is not generating any chlorine. It says that the temp. Is too low. Is there anything that I can do to correct the discrepancy in temperature. Charles View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Can the complete RJ-45 Plus System replace my current complete Si+ 45 System (Control Panel, Flow Sensor, Cell) WITHOUT cutting, gluing, retrofit any electrical connections, require professional installation? In other words, will the RJ-45 Plus Complete System be an easy Plug and Play to my existing system? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have an RJ-45 chlorinator. I checked the salt level (it is 3719), but the low salt light is on and the displays no water. I do not any cloudy water in the cell like it is usually when producing chlorine. View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
So I just got done cleaning my filter, remove the cell and cleaned it as well and added salt to the pool. I feel I put too much in because I’m getting a high salinity alarm. Do I need to drain water out of the pool and put untreated, water back into lower the salinity or will it still chlorinate and just have a high salt contact. View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have about 22 inches of straight pipe where I want to install this. If installing the flow switch and inverted cell on the same straight pipe, is the 6-12” of pipe before the flow switch required? Since it is the same straight pipe, can it be less? Or will the flow have to be installed after the cell? View answer
Asked 1 ´year ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
The RJ45+ is 6 years old. The unit shuts down on low salt every day have to turn power off to reset. I have tested the water at local Leslie pool store and they stated the salinity is 3300 PPM. I removed generator and found no scale but cleaned in muriatic acid bath anyway. No Scale was present in water after cleaning. the generator reads average of 3100 PPM salt and when chlorinating it reads 3500 PPM View answer
Asked 1 ´year ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have variable speed pump that has its own controller, so it is powered on all the time. Can I connect the CircuPool system to continous power and let the flow sensor determine when the system should generate chlorine? Otherwise I would need to manually coordinate a timer so that the CircuPool only comes on when the pump is running, and I'd rather not do that. View answer
Asked 7 ´years ago | Salt Chlorinators > CircuPool RJ-60 PLUS Salt Chlorine Generator
I have an old (and broken) Zodiac LM3-24 salt water generator installed on my pool. The previous owners of the house installed it and didn't maintain it very well, and the entire system is now in need of replacement. I am looking for a new system that I can fit into the existing space that the LM3-24 is currently occupying, without having to cut or drill anything. Will the CircuPool RJ-45 or -60 be a direct replacement for the LM3-24 that I have or will it require some extra cutting? I also have a Pentair Intellitouch i9+3 control panel. Will the RJ-45 or -60 interface with that system? View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool RJ-60 PLUS Salt Chlorine Generator
In what increments can you adjust the chlorine generation of the CircuPool RJ-60 PLUS ? In other words, each time you depress the ""+"" for greater prodution of chlorine, in what increment does the value of production increase? View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool RJ-60 PLUS Salt Chlorine Generator
