I have pentair equipment on my salt water system, I have an electronic switching system for exterior lights, spa, waterfall etc. which transmits wireless signals to my electrical enclosure outside.Can I find a replacement for it? Cost etc.?? View answer
Asked 7 ´years ago | Parts > Bypass Cell (fits Hayward® Aquarite®, Swimpure Plus®, CircuPool RJ, CircuPool Si)
I have a Compupol salt system, and your website states you sell compatible cells, but my pool guy notices that yours are a 3 prong plug in and mine is a two prong plug in. do you have 2 prong cells? View answer
Asked 1 ´year ago | Salt Cells > APX PERFORMANCE C10 Aftermarket Replacement Cell fits CompuPool CPSC-48 | up to 48,000 gallons
The original is rated for 60,000 gallons and produces >2lbs of chlorine per day. My Pool is 45,000 gallons so will this adequately handle the chlorine requirement? View answer
Asked 5 ´years ago | Salt Cells > APX PERFORMANCE C10 Aftermarket Replacement Cell fits CompuPool CPSC-48 | up to 48,000 gallons
what size is this. 2"? View answer
Asked 6 ´years ago | Generic Flow Switch (without PVC Fitting)
Does it have to be installed indoors? View answer
Asked 6 ´months ago
Can it be used in hot tub View answer
Asked 6 ´months ago
Replacement hayward turbocell tcells325 View answer
Asked 6 ´months ago | Support
IS this newer model a direct fit replacement for the original CORE-35 View answer
Asked 6 ´months ago
How does the pre-filter handle cotton wood? Does it clog the system, move to the clear collection area (ideal), or pass thru to the primary filter? Our current situation can create a blanket around our cartridge filter. View answer
Asked 2 ´years ago | Filters > CircuPool TJ-16 "Typhoon" Centrifugal Pre-Filter
Our big issue is hemlock needles. Much shorter than typical evergreen needles at about 1-1.5in so they get through the skimmer and filter baskets and once they clog the de filter they also don't rinse out with a backwash. But they are light enough to float. Will this pre filter help or will they get through because they aren't heavy enough? View answer
Asked 3 ´years ago | Filters > CircuPool TJ-16 "Typhoon" Centrifugal Pre-Filter
My PVC runs horizontal, and have pipe running parallel, under the section where I need to install this, which doesn’t leave me with enough clearance needed for the bottom of the cell. Can I pivot this when installing so the controls are back at an angle, and the bottom of the cell is more towards the front, to get around the PVC below? Or does this need to be installed straight up and down as shown? View answer
Asked 1 ´year ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
What are the dimensions of the unit. I need to know the width of hook-up from inlet to outlet hook-up and the distance from the centerline of the pipe hook-up to the bottom of the cartridge. View answer
Asked 1 ´year ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
Does it come with the PVC fittings that xxxx onto to the ends? The old ones on my Intellichlor are cracked and they have a slow drip leak. View answer
Asked 5 ´years ago | Salt Cells > APX PERFORMANCE P40 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC40® Salt Cells | up to 40,000 gallons
What are the dimensions of the O-Ring? The xxxx on cover I have is 5"" across and 4 5/8"" just inside the lip of the cover. I do not see any groove in the clear housing for an O-Ring. I have the Breeze Salt Generating System Model 760 and we just replaced the housing. View answer
Asked 2 ´years ago | Parts > SGS Breeze O-Ring
