Will this work on my system. I bought a salt cell T15 from you guys. The board reads 4000 amount of salt. I got it checked by Pinch a Penny pool store and it said 3100. I think the board is bad. Then i put my old salt cell back on and it read 3500 but it stills generating chlorin. The new salt cell does the same thing. View answer
Asked 5 ´years ago | Parts > Replacement Power PCB for Hayward® AquaRite® Circuit Board GLX-PCB-RITE (Aftermarket)
I need to remove and reinstall the salt cell container unit on my CircuPool RJ-30 PLUS Salt Chlorine Generator. That means that I'll need new collars. Is the Part Number: "COLLAR-RJN" the collar that threads to both ends of the salt cell capsule? View answer
Asked 5 ´years ago | Parts / Accessories > CircuPool® Threaded Cell Collar - RJ (3rd-Generation)
So when the time clock and pool are off, the control module shuts off too?Also my control module is mounted in direct sunlight and exposed to weather. Is the self contain unit ok or need to be in an additional inclosure?If I double the pool gallons to select the size of the generator is this enough? View answer
Asked 8 ´years ago | CircuPool RJ-20 PLUS Salt Chlorine Generator
Hello! I have an AstralPool generator from Australia, that is long past it's use. I'm looking to see how compatible your unit is as far as fittings. The configuration of my plumbing is such, that I need a similar unit. Tried AstralPool, but website ain't so hot. Thanks, Jeff C. View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool SJ-20 Salt Chlorine Generator
I have an above ground Intex pool and wanted to install a salt water system. Does it easily connect to my existing hoses or would I need special adaptors, also where do you get the salt and what kind do you buy? View answer
Asked 6 ´years ago | Salt Chlorinators > CircuPool SJ-20 Salt Chlorine Generator
I have a pool that was installed around 2008 (bought the house after it had been here several years) which has a Hayward Goldline AquaRite Salt system that currently has a T-CELL-15 40,000 gallon pool cell installed. The firmware version is r 1.40. Is there a replacement cell that would be plug and play that will work with this version, or is there a way to update the firmware?Thanks View answer
Asked 6 ´years ago | Salt Cells > CircuPool® GEN15 Aftermarket Replacement Cell fits Hayward® AquaRite® 40,000 Gal. Models
Does this come with an O ring? View answer
Asked 4 ´years ago | Parts > Winter Bypass Cap for CircuPool CORE-Series System
Does this fit the Core 35 Model? View answer
Asked 5 ´years ago | Parts > Winter Bypass Cap for CircuPool CORE-Series System
What exactly is the super chlorination mode on the p20 ? And is it necessary at installation if the chlorine level in the pool is already between 1.0 and 4.0 ppm ? View answer
Asked 2 ´years ago | Salt Cells > APX PERFORMANCE P20 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC20® Cells | up to 20,000 gallons
What is the maintenance like to acid wash the cell, for pentair I used a "stand" on the cell with a water / acid mix, does this use the same kinda stand? View answer
Asked 2 ´years ago | Salt Cells > APX PERFORMANCE P20 Aftermarket Replacement Cell fits Pentair® IntelliChlor® IC20® Cells | up to 20,000 gallons
Does this pump have a set of auxiliary contacts? I have a 400,000BTU gas heater that requires a certain amount of flow across the heat exchanger to operate safely and efficiently. If not, can you offer a simple solution to that requirement? I currently have a 2.5HP 2 speed pump running through a timer, a pair speed dip switches, and a pair of relays (Blue Haven control panel). There's 1 relay for each speed. The high speed control circuit interlocks with the heater. Thanks. View answer
Asked 5 ´years ago | [categoryname] > CircuPool SmartFlo® Variable Speed Pool Pump - 3.0 THP
