My pump runs 24hrs a day, 4 hours on a high setting and the rest on a low circulation. Will the cell also run 24hrs a day and therefore burn out in around 400 days? Should I put the cell on a timer or just let it run constantly? View answer
Asked 8 ´months ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
When using a variable speed pump that is self timed, the circupool SJ35 gets wired to a constant power source and is turned on and off by the flow control switch? Is the Circupool SJ35 a 120 or 220 system? View answer
Asked 4 ´years ago | Manufacturers > CircuPool > CircuPool SmartFlo® Variable Speed Pool Pump - 3.0 THP
If I connect this to an external timer, will this start self priming when power is connected? Also can you set the default speed it will then lower itself too automatically? It needs to retain this setting since external timer will disconnect power. View answer
Asked 6 ´years ago | Manufacturers > CircuPool > CircuPool SmartFlo® Variable Speed Pool Pump - 3.0 THP
I am using with a Pentair 520 Cartridge Filter. I would like to increase the water flo return in my pool which is 40,000 gallons, but was afraid the Pentair 520 cartridge filter could not handle the additional water flow? View answer
Asked 6 ´years ago | Manufacturers > CircuPool > CircuPool SmartFlo® Variable Speed Pool Pump - 3.0 THP
Does this pump have a set of auxiliary contacts? I have a 400,000BTU gas heater that requires a certain amount of flow across the heat exchanger to operate safely and efficiently. If not, can you offer a simple solution to that requirement? I currently have a 2.5HP 2 speed pump running through a timer, a pair speed dip switches, and a pair of relays (Blue Haven control panel). There's 1 relay for each speed. The high speed control circuit interlocks with the heater. Thanks. View answer
Asked 5 ´years ago | Manufacturers > CircuPool > CircuPool SmartFlo® Variable Speed Pool Pump - 3.0 THP
Just bought a new house with non-saltwater 20x40 ft pool. We want to change over to saltwater. All Q&A on this page refer to replacing an existing system. Can I use this system as an original installation? View answer
Asked 6 ´years ago | Salt Chlorinators > CircuPool Universal40 Salt Chlorine Generator
Dose it work with heater View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool Universal25 Salt Chlorine Generator
Can the salt cell be mounted at a slight upward angle or does it need to be perfectly horizontal or vertical. I have a good location to mount the cell but it is on a slight upward, approximately 15 degree angle. I would think it would be fine, bu I just wanted to verify for sure. View answer
Asked 6 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
When I was reading the installation instructions for the RJ45 plus, it states if using with a variable speed pump (on a low speed setting) that the cell must be inverted. If I'm installing the RJ45 plus vertically, does that mean I can't use the low speed on my variable speed pump? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have a 15,000-20,000 gallon in ground pool in the Dallas Texas Area. I would like to convert to saltwater and I am looking at the RJ+ series. Given the recommendation to upsize do you recommend a RJ30+ or RJ45+? Thanks View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Hello, I am considering the package deal for the variable speed pump and chlorinator. I currently have a Hayward Superpump II, 1HP single speed pump. We have a solar pool heater with a Hayward/Goldline 35 controller. Is there a way or an output on the pump that would trigger the solar controller only at higher pump speeds? Or is there a way for the solar controller to trigger the pump to go faster? I suspect I need to purchase a new controller as well. Is there a controller you'd recommend? It moves a Jandy valve to turn the solar on and off based on pool and solar temps.Thanks! View answer
Asked 6 ´years ago | Packages > Classic Combo (Medium Pools) - (RJ-30 PLUS Salt System + SmartFlo® VS Pump - 1.7 THP)
Is there a way to recalibrate the temperature sensor? My pool waterheater and pool thermometer both indicate that the pool is at 69 degrees F. But the readout on my RJ-60+ shows the water temp. to be around 50 deg F. As a result, the RJ-60+ is not generating any chlorine. It says that the temp. Is too low. Is there anything that I can do to correct the discrepancy in temperature. Charles View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have about 22 inches of straight pipe where I want to install this. If installing the flow switch and inverted cell on the same straight pipe, is the 6-12” of pipe before the flow switch required? Since it is the same straight pipe, can it be less? Or will the flow have to be installed after the cell? View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have RJ 20 system (6 years old},cell is over 3 years old.I did have low salt warning with correct salt level in pool, chlorine level was good.Now I have "no water flow" warning , Water flow is normal.chlorine production lower My question, do I have problem with cell? or problem with control unit? View answer
Asked 6 ´years ago | Salt Cells > CircuPool RJ20/AG16 Classic Replacement Cell (Electrode Only)
I have variable speed pump that has its own controller, so it is powered on all the time. Can I connect the CircuPool system to continous power and let the flow sensor determine when the system should generate chlorine? Otherwise I would need to manually coordinate a timer so that the CircuPool only comes on when the pump is running, and I'd rather not do that. View answer
Asked 7 ´years ago | Salt Chlorinators > CircuPool RJ-60 PLUS Salt Chlorine Generator
