I have the CircuPool Universal25 system and it's getting pretty old. The xxxx to control the chlorine production does not stay on the number it is set at and it's nearly impossible to select a number as it is too sensitive to movement. I'm considering upgrading to the RJ-20 system and wanted to know if the salt cell will fit into the plumbing connections I have in place for the Universal cell?? View answer
Asked 4 ´years ago | CircuPool RJ-20 PLUS Salt Chlorine Generator
I have a CircuPool Universal40 Salt Chlorine Generator system that I purchased in May of 2020. I just did my 3 month acid bath cell maintenance and removed all visible buildup but my Cell maintenance light is still blinking. There is proper water flow and control panel is reading approx 4.8 on cell and salt level is 3500. The manual says make sure the control module is set to the right cell version setting but how do I know what that system setting is? View answer
Asked 5 ´years ago | CircuPool UL40 Replacement Cell
Can the flow switch with the RJ45+ system be installed in a vertical position following a 90 degree elbow after where the cell is installed (horizontally)? This is the portion of the pipe before that is still visible before it goes underground to return water to the pool (i.e. the last point before water returns to the pool). View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I currently have an eco-smart pool system that uses a cartridge with copper electrodes for algae control and titanium electrodes for bacteria control. The pool has dissolved copper at a rate of 3-5ppm in it. Additionally the chemistry of the water requires 250-400 ppm calcium hardness. If I want to convert will Ihave to do something about the water chemistry? View answer
Asked 4 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have had this unit for just over 4 months. The percent generating is no longer working. For the last week the chlorine level in the pool has been very high. I have been bringing the generation down from the normal 40% to 30%, 20% and finaly 10%. The cell generate light never turns off, no matter when I look at it, it is on, unless I go to 0%. How do I get warranty help with this? View answer
Asked 2 ´years ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
Is there a way to recalibrate the temperature sensor? My pool waterheater and pool thermometer both indicate that the pool is at 69 degrees F. But the readout on my RJ-60+ shows the water temp. to be around 50 deg F. As a result, the RJ-60+ is not generating any chlorine. It says that the temp. Is too low. Is there anything that I can do to correct the discrepancy in temperature. Charles View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Can the complete RJ-45 Plus System replace my current complete Si+ 45 System (Control Panel, Flow Sensor, Cell) WITHOUT cutting, gluing, retrofit any electrical connections, require professional installation? In other words, will the RJ-45 Plus Complete System be an easy Plug and Play to my existing system? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
What are the dimensions of the O-Ring? The xxxx on cover I have is 5"" across and 4 5/8"" just inside the lip of the cover. I do not see any groove in the clear housing for an O-Ring. I have the Breeze Salt Generating System Model 760 and we just replaced the housing. View answer
Asked 2 ´years ago | Parts > SGS Breeze O-Ring
So I just got done cleaning my filter, remove the cell and cleaned it as well and added salt to the pool. I feel I put too much in because I’m getting a high salinity alarm. Do I need to drain water out of the pool and put untreated, water back into lower the salinity or will it still chlorinate and just have a high salt contact. View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have about 22 inches of straight pipe where I want to install this. If installing the flow switch and inverted cell on the same straight pipe, is the 6-12” of pipe before the flow switch required? Since it is the same straight pipe, can it be less? Or will the flow have to be installed after the cell? View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
The RJ45+ is 6 years old. The unit shuts down on low salt every day have to turn power off to reset. I have tested the water at local Leslie pool store and they stated the salinity is 3300 PPM. I removed generator and found no scale but cleaned in muriatic acid bath anyway. No Scale was present in water after cleaning. the generator reads average of 3100 PPM salt and when chlorinating it reads 3500 PPM View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Have a pool using a Hayward Aqua-rite T-3 is this T-9 a direct replacement? Would like to increase output. I know I will have to reprogram the control unit. Are control units same for all sizes of cells? When I say direct replacement I mean no plumbing, just unscrew old and xxxx on the new plus reprogram of course. View answer
Asked 9 ´years ago | Salt Cells > CircuPool® CIR-GEN9 Aftermarket Replacement Cell fits Hayward® AquaRite® 25,000 Gal. Models
Is the ""low salt"" and ""high salt"" determined in the RJ-45 Plus salt generating cell? I have lately have had the controller show ""low salt"" and ""check cell"" and I have carefully cleaned the cell as instructed 3 times in the last 4 weeks View answer
Asked 6 ´years ago | Salt Cells > CircuPool® RJ-45 PLUS Replacement Cell
I have the CircuPool Universal25 system and it's getting pretty old. The xxxx to control the chlorine production does not stay on the number it is set at and it's nearly impossible to select a number as it is too sensitive to movement. I'm considering upgrading to the RJ-20 system and wanted to know if the salt cell will fit into the plumbing connections I have in place for the Universal cell?? View answer
Asked 4 ´years ago | CircuPool RJ-20 PLUS Salt Chlorine Generator
