My pump runs 24hrs a day, 4 hours on a high setting and the rest on a low circulation. Will the cell also run 24hrs a day and therefore burn out in around 400 days? Should I put the cell on a timer or just let it run constantly? View answer
Asked 10 ´months ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
Can I buy a replacement cell for the RJ 30? View answers
Asked 2 ´months ago
Can the flow switch with the RJ45+ system be installed in a vertical position following a 90 degree elbow after where the cell is installed (horizontally)? This is the portion of the pipe before that is still visible before it goes underground to return water to the pool (i.e. the last point before water returns to the pool). View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I have had my chlorinator for 2 years. Recently it has been giving a low salt reading and not running. After testing salt (3600), cleaning and calibration of unit. It worked fine for 2 days. Now back to low salt setting and not working. Does the flow sensor need replacement? View answer
Asked 1 ´year ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
I have had this unit for just over 4 months. The percent generating is no longer working. For the last week the chlorine level in the pool has been very high. I have been bringing the generation down from the normal 40% to 30%, 20% and finaly 10%. The cell generate light never turns off, no matter when I look at it, it is on, unless I go to 0%. How do I get warranty help with this? View answer
Asked 2 ´years ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
I got a CFICGEN40 to replace my Pentair Intellichlor. The Pentair was installed vertically. The users manual says to install the replacement horizontally. Can the CFICGEN40 be installed vertically? View answer
Asked 3 ´years ago | Salt Chlorinators > APX PERFORMANCE P40 Complete Salt Chlorine Generator
I currently have an eco-smart pool system that uses a cartridge with copper electrodes for algae control and titanium electrodes for bacteria control. The pool has dissolved copper at a rate of 3-5ppm in it. Additionally the chemistry of the water requires 250-400 ppm calcium hardness. If I want to convert will Ihave to do something about the water chemistry? View answer
Asked 4 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Is there a way to recalibrate the temperature sensor? My pool waterheater and pool thermometer both indicate that the pool is at 69 degrees F. But the readout on my RJ-60+ shows the water temp. to be around 50 deg F. As a result, the RJ-60+ is not generating any chlorine. It says that the temp. Is too low. Is there anything that I can do to correct the discrepancy in temperature. Charles View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
Can the complete RJ-45 Plus System replace my current complete Si+ 45 System (Control Panel, Flow Sensor, Cell) WITHOUT cutting, gluing, retrofit any electrical connections, require professional installation? In other words, will the RJ-45 Plus Complete System be an easy Plug and Play to my existing system? View answer
Asked 3 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
What are the dimensions of the unit. I need to know the width of hook-up from inlet to outlet hook-up and the distance from the centerline of the pipe hook-up to the bottom of the cartridge. View answer
Asked 1 ´year ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
My PVC runs horizontal, and have pipe running parallel, under the section where I need to install this, which doesn’t leave me with enough clearance needed for the bottom of the cell. Can I pivot this when installing so the controls are back at an angle, and the bottom of the cell is more towards the front, to get around the PVC below? Or does this need to be installed straight up and down as shown? View answer
Asked 1 ´year ago | Salt Chlorinators > E-CHLOR Plug-In Electronic Chlorine Generator | APX PERFORMANCE | For Pools up to 32,000 Gallons
So I just got done cleaning my filter, remove the cell and cleaned it as well and added salt to the pool. I feel I put too much in because I’m getting a high salinity alarm. Do I need to drain water out of the pool and put untreated, water back into lower the salinity or will it still chlorinate and just have a high salt contact. View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
How many gallons are this system View answer
Asked 11 ´months ago | Salt Chlorinators > CircuPool Universal25 Salt Chlorine Generator
I have about 22 inches of straight pipe where I want to install this. If installing the flow switch and inverted cell on the same straight pipe, is the 6-12” of pipe before the flow switch required? Since it is the same straight pipe, can it be less? Or will the flow have to be installed after the cell? View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
The RJ45+ is 6 years old. The unit shuts down on low salt every day have to turn power off to reset. I have tested the water at local Leslie pool store and they stated the salinity is 3300 PPM. I removed generator and found no scale but cleaned in muriatic acid bath anyway. No Scale was present in water after cleaning. the generator reads average of 3100 PPM salt and when chlorinating it reads 3500 PPM View answer
Asked 2 ´years ago | Salt Chlorinators > CircuPool RJ-45 PLUS Salt Chlorine Generator
I've decided to go with the CORE55 unit. The installation video looks pretty simple, but the piping is 2"" and I have 1.5"" pipes and the total span I'll be install the unit into is 14-15 inches. Does the unit come with adapters for 1.5"" pipe and is the span from the filter to the return too short? View answer
Asked 5 ´years ago | Salt Chlorinators > CircuPool CORE-55 Salt Chlorine Generator
